iPW1iPW1EUROHF/50 MHz ALL BAND1 kW LINEAR AMPLIFIERINSTRUCTION MANUAL
System interconnections1 or 2 Icom 100 W HF transceivers can be connectedas exciters to the IC-PW1/EURO. Non-Icom trans-ceivers can be used, however
82INSTALLATION AND CONNECTIONS• Using a 13-pin ACC socket (IC-706 series)IC-PW1/EUROGroundCoaxial cable (supplied)ACC cable (supplied)Remote control c
92INSTALLATION AND CONNECTIONS• Using 1 Icom and 1 non-Icom exciters(transceivers)NOTE: The specifications for the SEND relay are5 V DC 0.1 A. If this
102INSTALLATION AND CONNECTIONS• Using non-Icom exciters (transceivers) when the IC-PW1/EURO’s power is OFFTo use the antenna selector of the IC-PW1/E
112INSTALLATION AND CONNECTIONSThe control section of the linear amplifier can be sep-arated from the main body, doubling as a remote con-troller. It c
123OPERATION Setting the ALC levelsBefore first applying power, make sure all connec-tions required for your system are complete by refer-ring to cha
133OPERATIONThe IC-PW1/EURO uses CI-V frequency data forautomatic selection of the operating band. Programthe exciter’s address to use this capability
143OPERATION Programming the CI-V address (continued)D Setting the IC-PW1/EURO’s addressIt is not necessary to change the IC-PW1/EURO’sdefault CI-V a
153OPERATIONt Push [DOWN] to turn the position memory functionfor the [INPUT] select switch ON.• The band indicators, [1.8]–[50], light continuously.y
163OPERATIONCAUTION:DO NOT operate the IC-PW1/EURO beforeadjusting the ALC levels properly with the [ALCadj1] and [ALC adj2] pots. (p. 11)It takes 15
RWARNING HIGH VOLTAGE! NEVERattach an antenna or internal antenna connector dur-ing transmission. This may result in an electricalshock or burn.RWARNI
173OPERATIONThis linear amplifier has various protection circuits.D ALC circuitThe ALC (Automatic Level Control) circuit automati-cally limits RF outpu
184MAINTENANCE TroubleshootingThe following chart is designed to help you correctproblems which are not equipment malfunctions.If you are unable to l
5SPECIFICATIONS19 General• Frequency coverage: 01.800–01.999 MHz03.500–13.999 MHz07.000–17.300 MHz10.100–10.150 MHz14.000–14.350 MHz18.068–18.168 MHz
205SPECIFICATIONSINSTALLATION NOTESFor amateur base station installations it is recom-mended that the forwards clearance in front of the an-tenna arra
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, JapanA-5449G-1EX-rPrinted in Japan© 1997–2007 Icom Inc.Printed on recycled paper with soy ink.
IMPORTANT ... iPRECAUTION ... iEXPLICIT DEFINITIONS
11PANEL DESCRIPTION Front panel and remote controller01002505001K1.5 K0TEMP ALCALC adjSWR011.523102030405060VDHOTIDPo102030405060WAMETER-1 METER-2PoT
21PANEL DESCRIPTIONq POWER SWITCH [POWER] (p. 12)Push momentarily to turn power ON.w TRANSMIT INDICATOR [TRANSMIT] (p. 16)Lights green while transmitt
31PANEL DESCRIPTION Rear panelq OUTPUT ANTENNA CONNECTORS [ANT1] – [ANT4] (p. 6)Accept a 50 Ω antenna with a PL-259 connector.w ACCESSORY SOCKET-1 [A
41PANEL DESCRIPTIOND ACC-1 SOCKETD ACC-2 SOCKET(w/[EXCITER] is “1”)The following descriptions are applied when the[EXCITER] switch is set to “1” (defa
52INSTALLATION AND CONNECTIONS UnpackingAfter unpacking, immediately report any damage to thedelivering carrier or dealer. Keep the shipping cartons.
GroundingTo prevent electrical shock, television interference(TVI), broadcast interference (BCI) and other prob-lems, ground the linear amplifier th
Commentaires sur ces manuels